top of page
Flats above a workshop desk, with a checklist reading Investigate, Model, Recommend.

Flat or Maisonette

Shared fabric. Limited Control.

Still a practical route forward.

Flats and maisonettes often have restricted control over

roofs and walls, and some improvements depend on the freeholder of the wider building.

​

Even so, there are usually worthwhile steps you can take within your own home.

​

This guide highlights the typical starting position, what matters most, and the routes we usually explore.

Typical Starting Position

Shared fabric
Who looks after the roof and outside walls? The answer helps separate work inside the flat from decisions for the whole block.

Heating type
Does the flat have its own boiler or electric heaters, or is heat supplied communally? Check which controls belong to the flat.

Hot water
Establish whether there is a cylinder and immersion heater inside the flat or a shared hot-water supply.

Typical starting position. Shared fabric: roofs and walls may involve freeholder or block control. Windows vary: some flats have mixed or ageing glazing. Heating type: electric, communal and gas systems behave differently. Hot-water setup: cylinder, immersion or communal supply can matter. Limited upgrade scope: not every EPC lever is within your control. Typical EPC starting point: around D or E, varying by building, systems and existing condition.

What Usually Matters Most

Meter and tariff
For an electrically heated flat, check the meter registers and tariff alongside the heating and hot-water schedules.

Heating controls
Check which rooms can be controlled separately and when the heating comes on.

Hot-water cylinder
Where there is a cylinder, check its insulation, thermostat and immersion timer.

Windows and glazing
Look for mixed glazing and draughts. Check who can approve repairs, replacement or secondary glazing.

Ventilation
Check the extract fans and air inlets, particularly where condensation appears.

Within your control
Check the lamps already fitted and other small changes you can make within the flat.

What usually matters most. Tariff and meter setup: the right arrangement can reduce costs. Heating controls: zoning or TRVs, timers and settings improve comfort and efficiency. Hot-water cylinder: insulation, timers and temperature settings make a difference. Glazing where practical: upgrade or add secondary glazing where suitable. Ventilation and condensation balance: keep air moving, reduce moisture and protect the fabric. Measures within your control: small steps add up and are always worth testing.

Possible Routes We Might Explore

A · Within your control
Review the meter, controls and hot-water settings. Test lighting and targeted draught reduction where relevant.

B · Targeted upgrade
Test selected glazing or secondary glazing and review ventilation. Establish what permissions the proposed work needs.

C · Whole building
Explore roof, wall or communal heating improvements with the freeholder or building manager.

Possible routes. Route A, within your control: tariff review and meter check, heating setup and controls, cylinder insulation and settings, draught sealing and insulation basics, lighting and easy wins. Usually the first route to test. Route B, targeted upgrade: selected glazing improvements, secondary glazing where suitable, internal improvements with permissions, ventilation review and upgrades. Useful where extra gains are available. Route C, whole building or later stage: roof or wall measures through the freeholder, communal-system improvements, larger block-wide works, solar or major works later. Depends on factors outside the flat.

Comparing the Routes

Route

A · Within your control

B · Targeted upgrade

C · Whole building

Relative cost

Route A · Lower cost

Route B · Medium cost

Route C · Higher cost

Disruption

Route A · Low disruption

Route B · Medium disruption

Route C · High disruption

What we’d need to confirm

Route A — confirm: Which changes can the flat owner make independently?

Route B — confirm: Which upgrades are practical and have permission?

Route C — confirm: Who would need to agree and organise the wider works?

These are illustrative comparisons. We model the EPC outcome for the proposed combination in your home.

Illustrative route comparison. Route A, within your control: lowest cost, low disruption, moderate likely SAP gain and three-star confidence. Route B, targeted upgrade: medium cost, medium disruption, good likely SAP gain and two-star confidence. Route C, whole building or later stage: highest cost, high disruption, highest likely SAP gain and one-star confidence.
What this journey usually teaches. Control matters: focus on what you can control and make every lever count. Use the levers you actually have: small, sensible steps may bring the best results. Some routes depend on the wider building: bigger gains may need partners, permissions or timing. Flats may need a realistic, staged route. Evidence may show that EPC C is difficult or not achievable without wider building works. A proper assessment makes the difference.

What This Journey Usually Teaches

Start with what the flat owner can change.
If the measures inside the flat fall short of band C, the assessment can show the remaining gap and which building-wide decisions could change the result.

Next steps: Investigate, Model, Recommend, beside an EPC Fellas mug and notebook.

Does this look like your property?

Book an Improvement Assessment and we’ll test the
routes that genuinely make a difference.

The EPC Fellas workshop hat filled with surveying tools

A flat.

Use the levers you actually have. A typical guide; your flat needs its own assessment.

Typical Improvement Journeys

Flat or Maisonette

Shared fabric. Limited Control.
Still a practical route forward.

Which improvements can you make inside the flat, and which depend on the wider building? The answer shapes the order in which we test the options.

Typical Starting Position

Shared fabric

Roof and wall improvements may involve the freeholder or building manager.

Heating type

Electric heaters, communal heating and a gas boiler offer different options for control.

Hot water

Check whether the flat has its own cylinder and immersion or receives a communal supply.

What Usually Matters Most

Start with the heating, hot water and controls you can actually change. In an electrically heated flat, the meter and tariff arrangement is worth checking. Mixed glazing, draughts and condensation may point to further work.

Possible Routes We Might Explore

A · Within your control

Review the meter and tariff, heating controls, cylinder insulation and settings. Test simpler measures such as draught reduction and lighting where relevant.

B · Targeted upgrade

Consider selected glazing, secondary glazing or internal improvements where practical and permitted. Review ventilation alongside them.

C · Whole building or later stage

Explore roof, wall or communal heating improvements with the people responsible for the building. Solar or other major works may depend on a wider programme.

Comparing the Routes

A · Within your control
Lower cost, low disruption
Illustrative confidence: 3 stars

B · Targeted upgrade
Medium cost and disruption
Illustrative confidence: 2 stars

C · Whole building or later stage
Higher cost, high disruption
Illustrative confidence: 1 star

These are illustrative comparisons. The assessment tests the EPC outcome for the proposed combination in your home.

What This Journey Usually Teaches

Where the measures available inside the flat fall short of C, a useful assessment identifies the remaining gap and which building-wide decisions could change the result.

Does this look like your property?

Book an Improvement Assessment and we’ll test the routes that genuinely make a difference.

Book an EPC Improvement Assessment

Back to Typical Journeys

Choose the help you need.

1. Establish control

Check which measures are yours to change and which depend on a freeholder, communal system or wider building.

2. Review the systems

Check heating, controls, meter and tariff arrangements, plus hot-water storage where present.

3. Compare the routes

Model suitable improvements within your control first. Explore glazing or wider building works where permissions and timing allow.

A realistic route may need partners.

Some flats need wider building works to reach a target. Distinguish operating advice from verified EPC inputs, and check permissions before recommending work.

Good Advice. Better Decisions

01256 975 995 / 07879 653 745

Every Good Survey Begins With Good Questions

Good Advice. Better Decisions

01256 975 995 / 07879 653 745

Every Good Survey Begins With Good Questions

bottom of page